SpeedyBee F7 V3 50A Stack F722 Flight Control BL32 50A 4in1 ESC3~6S Lipo With

Parameters:Name:SpeedyBee F7 V3 Flight ControllerMCU:F722IMU(Gyro):SBMI270USB Port Type:SType-CBarometer:SBMP280OSD :SAT7456E BLE Bluetooth:Supported. Used for Flight Controller configurationFlash FC Firmware Wirelely:SSupported. Please enter MENU > FC Firmware FlasherDownload/Analyze Blackbox:Supported.Please enter MENU > Blackbox AnalyzerAir Unit Connection Way:Two ways supported: 6-pin connector or direct soldering.Flash(for BlackBox):500MBBetaFlight Camera Control Pad:Yes(CC pad on the front side)Power Input:3S - 6S Lipo5V Output:10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A.9V Output:2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A.3.3V Output:Supported. Designed for 3.3V-input receivers. Up to 500mA current load.4.5V Output:Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.ESC Signal Pads:M1 - M4 on bottom side and M5-M8 on front side.UART:5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)ESC Telemetry UART:R4(UART4)I2C:Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.LED Pad:Used for WS2812 LED controlled by Betaflight firmware.Buzzer:BZ+ and BZ- pad used for 5V BuzzerBOOT on:Supported.[A]. Pre and hold BOOT on and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT on can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-pre the BOOT on to cycle the LED displaying mode. Long-pre the BOOT on to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.RSSI Input:Supported. Named as RS on the front side.SmartPort:Use any TX pad of UART for the SmartPort feature.Supported Flight Controller Firmware:BetaFlight(Default), EMUFlight, INAVFirmware Target Name:SPEEDYBEEF7V3Mounting 30.5 x 30.5mm( 4mm hole diameter)Dimension:41(L) x 38(W) x 8.1(H)mmWeight:10.7gSpeedyBee BL32 50A 4-in-1 ESCFirmware:SpeedyBee BL32 50AConfigurator Download Link:http://github.com/bitdump/BLHeli/releasesContinuous Current :50A * 4Burst Current:55A(5S)TVS Protective diode:YesHeat Sink:YesExternal Capacitor:1500uF Low ESR Capacitor(In the package)ESC Protocol:DSHOT300/600Power Input:3-6S LiPoPower Output:VBATCurrent r:Support (Scale=490 Offset=0)Mounting:30.5 x 30.5mm( 4mm hole diameter)Dimension:45.6(L) * 40(W) * 8.8mm(H)Weight:19.2g with heat sinkPackage Included:SpeedyBee F7 V3 50A Flying Tower (F7 V3 Flight Control BL32 50A 4in1 ESC) x 1

About shipping
Shipping and Packaging All itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very important to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.