L298 New Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for stepper motor smart car robot

L298 New Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for stepper motor smart car robot

• I am an international seller

Our shop sells the most popular 3C consumer electronics products,such as mobile phone accessories,computer accessories,game peripherals,smart wearables,and follow the most popular fashion trends. If you like our products,please follow us,become our follower and fan.We will provide you with the most popular products to satisfy your fashion shopping experience.Package : SMDis_customized : YesModel Number : L298NOperating Temperature : 1.5ADissipation Power : 2-way DC motor drive moduleSupply Voltage : 2v-10vApplication : ComputerCondition : NewType : Voltage RegulatorBrand Name : TENSTAR ROBOTOrigin : Mainland ChinaModule name  : dual H bridge motor drive moduleWork mode      : H bridge drive (double road)Main control chip  : L298NPackaging      : electrostatic bagLogical voltage  : 5VDrive voltage  : 5v-35vLogical current  : 0mA-36mADriving current  : 2A(MAX single bridge)Storage temperature   : - 20 ° to + 135 °Maximum power    : 25WWeight     : 30 gPeripheral dimensions : 43*43*27mmProduct features:This module USES L298N as the main drive chip, with strong driving ability, low heat and strong anti-interference ability.Through this module can use the built-in 78 m05 drive power supply parts of their work, but in order to avoid the voltage regulator chip damage, when using the driving voltage is greater than 12 v, please use the external power supply 5 v logic.This module USES a large capacity filter capacitance, a continuation protection diode, can improve reliability.Notes:1. When you are driving voltage (above logo for the 12 v input, can actually accept input range is 7 to 12 v) for 7 v to 12 v, can make to onboard power supply 5 v logic, when using the onboard after 5 v power supply, interface of + 5 vThe power supply does not input voltage, but can yield 5V voltage for external use.2. When the driving voltage is higher than 12V, it is less than or equal to 24V(the chip manual proposes to support 35V, but according to the bookWhen the maximum voltage is applied to the maximum voltage of 298 conservative applications to 24V, for example, the motor with a rated voltage of 18V shall be driven.You must first remove the board 5V output to enable the jumper cap. Then 5V is accessed outside the 5V output portThe 5V enables the power to be a control signal with a level of 5V. When the signal input is valid, and when the power supply is normal in the motor drive module, the motor drive module outputs the current. Otherwise, even if the power supply is normal, there is no current on the motor.Voltage to L298N internal logic circuit power supply. (this is a high-pressure, unconventional app!)Module name  : dual H bridge motor drive moduleWork mode      : H bridge drive (double road)Main control chip  : L298NPackaging      : electrostatic bagLogical voltage  : 5VDrive voltage  : 5v-35vLogical current  : 0mA-36mADriving current  : 2A(MAX single bridge)Storage temperature   : - 20 ° to + 135 °Maximum power    : 25WWeight     : 30 gPeripheral dimensions : 43*43*27mmProduct features:This module USES L298N as the main drive chip, with strong driving ability, low heat and strong anti-interference ability.Through this module can use the built-in 78 m05 drive power supply parts of their work, but in order to avoid the voltage regulator chip damage, when using the driving voltage is greater than 12 v, please use the external power supply 5 v logic.This module USES a large capacity filter capacitance, a continuation protection diode, can improve reliability.Notes:1. When you are driving voltage (above logo for the 12 v input, can actually accept input range is 7 to 12 v) for 7 v to 12 v, can make to onboard power supply 5 v logic, when using the onboard after 5 v power supply, interface of + 5 vThe power supply does not input voltage, but can yield 5V voltage for external use.2. When the driving voltage is higher than 12V, it is less than or equal to 24V(the chip manual proposes to support 35V, but according to the bookWhen the maximum voltage is applied to the maximum voltage of 298 conservative applications to 24V, for example, the motor with a rated voltage of 18V shall be driven.You must first remove the board 5V output to enable the jumper cap. Then 5V is accessed outside the 5V output portThe 5V enables the power to be a control signal with a level of 5V. When the signal input is valid, and when the power supply is normal in the motor drive module, the motor drive module outputs the current. Otherwise, even if the power supply is normal, there is no current on the motor.Voltage to L298N internal logic circuit power supply. (this is a high-pressure, unconventional app!)Product :1. Driver chip: L298N dual H-bridge driver chip2. The power supply range of the driving part terminal VMS: +5V～＋35V3. Drive partial peak current Io: 2A/bridge4. The power supply range of the logic part terminal Vss: 4.5-5.5V5. Logic part operating current range: 0～36mA6. Control signal input voltage range: high level 4.5-5.5V, low level 0V7. Maximum power consumption: 20W8. Storage temperature: -25℃～＋130℃9.Drive board size: 55mm*60mm*30mm10. Drive board weight: 33g11. Other functions: control direction indicator light, power supply indication, current detection, and power interface in the logic part of the board.This L298N driver module, using ST's L298N chip, can directly drive two 3-30V DC motors, and provides a 5V output interface, which can supply power to the 5V microcontroller circuit system, supports 3.3VMCU control, and can conveniently control the speed of DC motors And direction, can also control 2-phase stepper motor, it is necessary for smart car.