Aluminum M.2 NVME SATA SSD Enclosure Adapter, USB 3.2 Gen 2 (10 Gbps) to NVME PCI-E SATA M-Key/(B+M) Key Solid State Drive External Enclosure Support UASP Trim for NVME/SATA SSDs 2242/2260/2280

SSK USB C M.2 NVMe SATA（NGFF）SSD Enclosure (Double Protocol SSD)

M.2 NVMe PCIE /SATA（NGFF）SSD Based

SSK M.2 NVME SATA SSD Enclosure adopts high performance controller Chipset RTL9210B, with high-speed data transmission speeds up to 10Gbps . 1GB file only takes 1 second ;

Attention: It supports PCI-E based M key / (B&M) key M.2 NVME SSD read/write speed up to 10Gbps; SATA-based B&M Key M.2 SSD read/write speed up to 6bps. Not compatible with B Key Connectors. Does not support M.2 PCIe AHCI SSDs, M.2 PCIe devices such as WiFi and capture cards, mSATA SSDs, and non-M.2 form factor SSDs.

M.2 NVME PCIe M key & M.2 SATA (NGFF) B&M key Enclosure Adapter

• Only compatible with NVME and sata M Key and B+M connectors
• Not compatible with B Key Connectors.
• Does not support M.2 PCIe AHCI SSDs, M.2 PCIe devices such as WiFi and capture cards, mSATA SSDs, and non-M.2 form factor SSDs.

Attention: NVMe and SATA SSDs are not included.

Fashion Design for Excellent Heat Dissipation

Adopts aluminum alloy shell, Slim design, and excellent heat dissipation, be portable and easy to carry.

Attention:

Due to the nvme SSD extreme transmission speed, the temperature is higher than USB3.0 HDD, we tested ours is around 50 °C in writing and below 40 °C in reading, even after a long time R/W, the speed will not drop down or device will not shut down

Extreme Data Transfer

With USB 3.1 Gen2 interface, provides transfer speeds of up to 1000MB/s,1GB file1 second. Backward compatible with USB 3.1/3.2 Gen2 and USB 3.1 up to 10Gbps.

Notice :

Insert your NVMe or SATA SSD into the enclosure and connect to your laptop’s USB-C or Thunderbolt 3 port to transfer movies, music.

The actual speed depends on the speed of your SSD, USB Port type, your computer performance etc, nvme ssd is not included.

SSD needs to be fully inserted for working

If there is a fatal errors or SSD can not be recognized: First, Please confirm your SSD is M.2 PCIE NVME SSD. Second, please confirm whether your SSD is fully inserted into the NVME Slot. If not, you need to push the SSD into the PCIE NVME Slot at a 45 degree angle. The pins of the SSD will be fully seated and covered.

Easy Installation

With screw driver, no additional tools required. With two cables, USB A to C and USB C to C which suitable for all Host PC ports.

Supports Plug & Play and Hot-Swapping.

Copper Strip + Thermal Conductive Pad for Excellent Heat Dissipation

SSK Enclosure not only adopts the larger copper strip for heat dissipation, but also have a special design, it adds a plastic shrapnel which can lift SSD slightly. With the thermal pad, the lifted SSD can be tightly attached to the Aluminium shell, so as to achieve the purpose of rapid heat dissipation.

Multi OS Compatible

• Windows 7 or above, Mac OS 10.10.5 or above, Linux, and Type C Android Phones.
• Blue Indicator is always on when plug in, and flash when read or write data.

Attention:

1. It requires 2 screws and 1 washer to assemble the enclosure. When install the round washer to assemble SSD and PCB, please pay attention to the thickness of the washer, it has two directions, please keep upper thin and bottom thick. When insert the pcb to house casing, as it is shrapnel design, pls press down the PCB slightly to ensure the proper insertion.

2. After installed, when the first time to use the new SSD, it may not be found, please partition and format it first under disk management, then it can be used normally. If want to work on both Mac and Windows OS, please format it to EXFAT.

3. Please kindly note our item works well on all brands M.2 NVME PCIe and SATA NGFF 2242, 2260, 2280mm SSD up to 4TB including Intel 600p, 660p, Samsung, WD, Crucial etc.

• Not compatible with MacBook original SSD!

4. Due to the transmission speed is extreme fast for nvme ssd, the temperature is relatively higher than USB3.0 HDD, but because of our unique product design, the whole SSD case can be worked as the thermal pad, it can rapidly dissipate the heat and protect the SSD. Please let us know and we will reply asap and give you a happy solution.

• According to the New USB-IF standard, the USB 3.2 specification replaces the USB3.0 USB3.1 specification and it introduced a new nomenclature, the USB 3.2 specification absorbed all prior USB 3.0/3.1 specifications, So, our 10Gbps USB C NVME SSD Enclosure, we can say USB3.1 Gen 2 or USB3.2 Gen 2(Old Nomenclature /New Nomenclature)

USB 3.2 New Nomenclature:

1. USB3.2 Gen 1 = USB3.1 Gen 1 , Product transfer rate is up to 5Gbps, Marketing name: SuperSpeed USB

2. USB3.2 Gen 2 = USB3.1 Gen 2 , Product transfer rate is up to 10Gbps, Marketing name: SuperSpeed USB 10Gbps

3. USB3.2 Gen 2X2, Product transfer rate is up to 20Gbps, Marketing name: SuperSpeed USB 20Gbps