This website uses cookies. For further information on how we use cookies you can read our Privacy and Cookie notice
HomeElectronicsHome AudioHome Theater SystemsSpeaker SystemsCeiling & In-Wall Speakers1Hz-50MHz Frequency Counter Kit DIY for Oscillator, Crystal
KSh 1,601
KSh 3,04147%
2 units left
+ shipping from KSh 261 to CBD - UON/Globe/Koja/River Road
0 out of 5
(No ratings available)Promotions
Delivery & Returns
Shipped from abroad
Choose your location
Pickup Station
Delivery Fees KSh 261
Ready for pickup between 19 June & 22 June when you order within next 7hrs 51mins
Door Delivery
Delivery Fees KSh 362
Ready for delivery between 19 June & 22 June when you order within next 7hrs 51mins
Return Policy
Easy Return, Quick Refund.Details
Warranty
None
Seller Information
Nehami
66%Seller Score
13 Followers
Seller Performance
Order Fulfillment Rate: Poor
Quality Score: Excellent
Customer Rating: Average
Product details
You can use the universal USB 5V interface power supply, can also use an external DC power supply or 9V battery.
The number of components is small, all straight-line components, installation and commissioning simple.
Addition and subtraction frequency for the measurement of radio transceivers and other equipment.
You can select the power saving mode, if the frequency is not obvious changes within 15 seconds automatically turn off the display.
Measurable frequency range 1 Hz -50 MHz. Can measure the oscillation frequency of most commonly used crystal. The crystal oscillator of 32.768KHZ cannot be measured. Only the crystal oscillator of 4-20MHZ can be measured under limited conditions, and the crystal oscillator of 48MHZ can also be measured. However, because this crystal oscillator uses 3 harmonics, the measurement of the 48MHZ crystal oscillator will display the fundamental frequency of 16MHZ. ,As shown :
You can also directly input the frequency signal between IN and G (ground) for measurement, and pay attention that the amplitude of the measurement signal should not be higher than 5V to avoid damage to the IC. The following shows the display of input 1HZ and 10KHZ:
All in-line components can be soldered correctly according to the PCB silk screen. After soldering, use the standard signal source to input the signal, and adjust the yellow adjustable capacitor to make the displayed value to the signal frequency. You can use signal generator to adjust, if there is no standard signal, you can also use a crystal oscillator with better accuracy for direct calibration.
The power supply can use a USB to 3.5mm power cable, or directly input 5-9V DC power supply at the - and + pads.
colour: red
Material: PVC
Size: 10x5x5cm Package Contents:
1 x frequency meter(requires assembly) Only the above package content, other are not included.
Note: Light and different displays may cause the color of the item in the a little different from the real . The measurement allowed error is +/- 1-3cm.
The number of components is small, all straight-line components, installation and commissioning simple.
Addition and subtraction frequency for the measurement of radio transceivers and other equipment.
You can select the power saving mode, if the frequency is not obvious changes within 15 seconds automatically turn off the display.
Measurable frequency range 1 Hz -50 MHz. Can measure the oscillation frequency of most commonly used crystal. The crystal oscillator of 32.768KHZ cannot be measured. Only the crystal oscillator of 4-20MHZ can be measured under limited conditions, and the crystal oscillator of 48MHZ can also be measured. However, because this crystal oscillator uses 3 harmonics, the measurement of the 48MHZ crystal oscillator will display the fundamental frequency of 16MHZ. ,As shown :
You can also directly input the frequency signal between IN and G (ground) for measurement, and pay attention that the amplitude of the measurement signal should not be higher than 5V to avoid damage to the IC. The following shows the display of input 1HZ and 10KHZ:
All in-line components can be soldered correctly according to the PCB silk screen. After soldering, use the standard signal source to input the signal, and adjust the yellow adjustable capacitor to make the displayed value to the signal frequency. You can use signal generator to adjust, if there is no standard signal, you can also use a crystal oscillator with better accuracy for direct calibration.
The power supply can use a USB to 3.5mm power cable, or directly input 5-9V DC power supply at the - and + pads.
colour: red
Material: PVC
Size: 10x5x5cm Package Contents:
1 x frequency meter(requires assembly) Only the above package content, other are not included.
Note: Light and different displays may cause the color of the item in the a little different from the real . The measurement allowed error is +/- 1-3cm.
Specifications
Key Features
- Durable and good quality
- 1Hz-50MHz
- 1Hz-50MHz Frequency
- frequency counter
- frequency meter
- DIY Module
- The details are as described above
What’s in the box
1 x frequency meter(requires assembly)
Specifications
- SKU: 91933EA26LB0CNAFAMZ
- Model: module
- Production Country: China
- Size (L x W x H cm): 12x9x2
- Weight (kg): 0.034
- Main Material: PVC
- Warranty Address: None
Customer Feedback
This product has no ratings yet.
915 Generation 1Hz-50MHz Frequency Counter Kit DIY for Oscillator, Crystal
KSh 1,601
KSh 3,04147%
Questions about this product?